Eduqas GCSE Electronics
cookie 製作的考試準備筆記,共 20 篇,分為 9 個部分,依照課程主題編排。
Notes for Eduqas GCSE (9-1) Electronics (WJEC C490), in folders for the specification's topics in its order: systems, resistors, switching, logic, amplifiers, timing, interfacing and design. Follows the 2017 specification, version 5 (December 2025).
內容
第一則筆記
Systems and circuit concepts / Electronic systems and sub-systems
Most electronic systems can be described as three sub-systems working in a chain: a sensing sub-system, a processing sub-system and an output sub-system. The sensing sub-system detects something in the physical world and turns it into an electrical signal. The processing sub-system decides what to do with that signal. The output sub-system does something visible, audible or physical with the result. A burglar alarm, an automatic night light and a washing machine's door interlock all fit this pattern, even though they look very different.
Sensing sub-systems
A sensor is a transducer, a component that converts one form of energy into another. Each sensor responds to a particular quantity:
| Quantity detected | Typical sensor |
|---|---|
| Light | Light dependent resistor (LDR) |
| Temperature | Thermistor (negative temperature coefficient) |
| Magnetic field | Magnetic field sensor or reed switch |
| Pressure | Pressure sensor |
| Moisture | Moisture sensor (two electrodes that change resistance when wet) |
| Sound | Microphone |
| Rotation | Potentiometer or rotary sensor |
Most sensors change their resistance, not their output voltage directly. A sensor's resistance is therefore turned into a voltage by placing it in a voltage divider, which is covered in the note on voltage dividers. The output of a sensing sub-system is usually an analogue voltage that varies smoothly with the quantity being measured.
Processing sub-systems
The processing sub-system takes the signal from the sensor and produces a decision. The building blocks are:
- logic gates (NOT, AND, OR, NAND and NOR), which combine digital signals;
- a latch, which stores a single bit so that the output holds its value after the input changes;
- a time delay, usually an RC network or a 555 timer, which holds a signal for a set time;
- a comparator, which compares an input voltage with a reference voltage and gives a high or low output.
A comparator is the usual link between an analogue sensor and digital logic, because it turns a voltage that varies continuously into one of two levels.
Output sub-systems
Output devices change electrical energy into another form:
- a lamp or LED produces light;
- a buzzer or loudspeaker produces sound;
- a solenoid uses an electromagnet to push or pull a plunger in a straight line;
- a motor produces continuous rotation;
- an actuator, such as a servo, turns through a set angle under the control of an input signal.
Each output device needs a particular current and voltage to work. A motor, for example, may need far more current than a logic gate can supply.
Transducer drivers
A transducer driver is the circuit between a processing sub-system and an output device. A logic output cannot usually supply enough current to drive a motor, a relay coil or a lamp directly, so the driver switches the larger current from a separate supply. An n-channel MOSFET or an npn transistor is often used for this, because a small signal at the gate or base controls a large current through the load. The driver therefore protects the processing sub-system from the load and allows the output device to run from a suitable supply.
Designing and testing a system
A system is designed by stating what it must do, dividing it into sub-systems, and choosing components for each one. Each sub-system is then built and tested on its own before the sub-systems are connected. This makes faults easier to find: if the whole system fails, the test results show which sub-system to check first.
A block diagram is the usual way to show the design. Each sub-system is drawn as a labelled box, with arrows showing the direction of the signals between them. The arrows matter as much as the boxes, because they show which sub-system depends on which.
還有 19 個:可以從上方清單開啟任何一個。
評分
還沒有文字評論。把這些筆記加到自己的筆記中,就能成為第一個留下評論的人。