Pular para o conteúdo

Eduqas A level Electronics

A-Level · EduqasElectronics19 notas em 15 pastas, 66 KB

19 notas de revisão de Eduqas A-Level Electronics, criadas por cookie, em 15 seções que seguem os tópicos do curso.

Revision notes for Eduqas A level Electronics (WJEC Eduqas GCE A level in Electronics, teaching from 2017, for award from 2019), in folders by topic in the specification's order: semiconductors, logic, operational amplifiers, signal conversion, AC circuits and filters, communications, instrumentation, timing circuits, sequential logic, microcontrollers, digital and optical communication, power supplies, high-power switching and audio systems.

O que contém

A primeira anotação

Semiconductors / Semiconductors and diodes

Conduction in silicon

Pure silicon is a semiconductor. At room temperature very few electrons are free to move, so it conducts poorly. Adding a small amount of another element, a process called doping, changes its conducting properties greatly.

n-type and p-type material

Doping with a group 5 element such as phosphorus adds an extra electron to the crystal for each atom. These electrons are free to move, so electrons are the majority carriers in n-type material and holes are the minority carriers.

Doping with a group 3 element such as boron does the opposite. Each atom leaves a gap in the bonding, called a hole. A hole behaves as a positive charge carrier: when a neighbouring electron moves into it, the gap moves to where the electron was. Holes are the majority carriers in p-type material and electrons are the minority carriers.

The p-n junction

Joining p-type and n-type material in one crystal gives a p-n junction. Electrons near the junction on the n side diffuse across and fill holes on the p side. This leaves a depletion region, with no free charge carriers, and a small built-in barrier that opposes further movement.

With forward bias the p side is connected to the positive terminal. The barrier shrinks, and once the voltage passes about 0.6 to 0.7 V for silicon, a large current flows. Above that point the voltage across the diode changes little as the current rises.

With reverse bias the depletion region widens and only a very small leakage current flows, until the reverse voltage is high enough to cause breakdown.

Light-emitting diodes

In a forward-biased LED, electrons cross the junction and recombine with holes. Each recombination releases energy as a photon of light. The colour depends on the semiconductor material used.

An LED is normally run from a supply through a series resistor:

R=VS−VFIR = \frac{V_S - V_F}{I}

Here VSV_S is the supply voltage, VFV_F is the forward voltage of the LED and II is the current wanted through it.

Worked example: a 9 V supply, an LED with VF=2V_F = 2 V and a wanted current of 20 mA.

R=9−20.020=350 ΩR = \frac{9 - 2}{0.020} = 350\ \Omega

The nearest preferred value above that is 390 Ω. It gives a current of 7/390=17.97 / 390 = 17.9 mA, which is safely below the LED's maximum.

Photodiodes

A photodiode is operated in reverse bias. Light absorbed near the junction creates electron-hole pairs, which increase the reverse current. The current rises with the intensity of the light falling on it, so a photodiode turns light into a current that can be measured or amplified.

Zener diodes

A zener diode is made to conduct in reverse breakdown at a fixed voltage, its zener voltage VZV_Z. Once breakdown starts, the voltage across the zener stays close to VZV_Z while the current through it changes. This is why a zener diode is used for voltage regulation. A series resistor limits the current through it, and the load is connected across it.

Diode characteristics

A diode's current-voltage graph is highly non-linear. In forward bias there is almost no current below the threshold, then the current rises steeply. In reverse bias the current is tiny and nearly constant until breakdown, when it rises sharply. Because of this shape, a diode cannot be treated as a resistor: its resistance depends on the current through it.

Why the colour depends on the material

When an electron falls across the band gap of the semiconductor and recombines, it releases an energy EE equal to the band gap. The photon has frequency f=E/hf = E/h, and wavelength λ=c/f\lambda = c/f. Written in electronvolts and nanometres, λ=1240/E\lambda = 1240 / E nm, where EE is in electronvolts.

Worked example: a band gap of 2.0 eV gives a wavelength of 1240/2.0=6201240 / 2.0 = 620 nm, which is orange-red light. A band gap of 3.0 eV gives 1240/3.0≈4131240 / 3.0 \approx 413 nm, which is violet.

Diodes in rectifiers

Because a forward-biased diode conducts and a reverse-biased diode blocks, it lets only one direction of current through. A single diode in series with an AC supply gives a half-wave output. The rectifiers in a later section use four diodes or a centre-tapped transformer to pass both halves of the cycle.

E mais 18: abra qualquer um deles na lista acima.

Avaliações

Ainda não há avaliações escritas. Adicione estas notas às suas e você poderá ser a primeira pessoa a deixar uma avaliação.