Eduqas A-Level Physics
52 notatki do nauki, utworzonych przez cookie, w 7 sekcjach zgodnych z tematami kursu.
Notes for Eduqas A-Level Physics (A420), in folders for the three components of the specification in its order, with the required practicals in the topics they belong to. The four optional topics (alternating currents, medical physics, the physics of sports, energy and the environment) each have their own folder. Delete the options and folders your course leaves out.
Co zawiera
Pierwsza notatka
Newtonian physics / Units, vectors and density
SI base units
Every physical quantity is measured in a unit that can be built from a small set of base units. Six of them are needed for this course.
| Quantity | Base unit | Symbol |
|---|---|---|
| Mass | kilogram | kg |
| Length | metre | m |
| Time | second | s |
| Electric current | ampere | A |
| Amount of substance | mole | mol |
| Thermodynamic temperature | kelvin | K |
Every other unit is a derived unit, a product or quotient of base units. The newton is the force that gives a mass of 1 kg an acceleration of 1ms−2, so 1N=1kgms−2. The joule is a newton metre, so 1J=1kgm2s−2, and the watt is a joule per second, so 1W=1kgm2s−3. The coulomb is an ampere second, the volt is a joule per coulomb, which gives 1V=1kgm2s−3A−1, and the ohm is a volt per ampere, so 1Ω=1kgm2s−3A−2.
Prefixes
A prefix multiplies the unit by a power of ten. The ones used most are tera (T, 1012), giga (G, 109), mega (M, 106), kilo (k, 103), centi (c, 10−2), milli (m, 10−3), micro (μ, 10−6), nano (n, 10−9), pico (p, 10−12) and femto (f, 10−15). The prefix belongs to the whole unit that follows it, so 1cm3=(10−2m)3=10−6m3, not 10−2m3. This is the commonest source of a wrong power of ten when converting areas and volumes.
Checking an equation for homogeneity
An equation is homogeneous when every term has the same units. A correct physical equation must be homogeneous, so writing each side in base units is a check on an equation that has been remembered or derived. It cannot prove an equation right, because it is blind to pure numbers such as 21 or 2π, but it will catch a wrong power or a missing quantity.
As an example, the equation for the period of a simple pendulum is T=2πl/g. The units of l/g are m/ms−2=s2, so the square root has the unit of seconds, which matches T. The same idea can be used to find an unknown unit. The Young modulus is stress over strain, strain has no unit, and stress is Nm−2, so the Young modulus is in Nm−2=kgm−1s−2.
Scalars and vectors
A scalar quantity has magnitude only. A vector quantity has magnitude and direction. The distinction matters because vectors must be added with their directions taken into account.
| Scalars | Vectors |
|---|---|
| speed, distance, time, mass | displacement, velocity, acceleration |
| density, pressure, temperature | force, momentum, weight |
| energy, work, power | electric and magnetic field strength |
A vector is drawn as an arrow whose length represents its magnitude, pointing in its direction. Two opposite directions along a line are distinguished by a sign, and the sign is part of the vector: a velocity of −3ms−1 is three metres per second in the direction taken as negative.
Adding vectors
Two vectors are added by placing the tail of the second at the head of the first. The resultant goes from the tail of the first to the head of the second. The order does not matter. Subtracting a vector is the same as adding its reverse, and a reversed vector has the same length and the opposite direction. Only two perpendicular vectors need be combined by calculation. If A and B are at right angles, the resultant R has
where θ is the angle between R and A. A boat heading due north at 4.0ms−1 through water in a river that flows east at 3.0ms−1 has a velocity relative to the bank of magnitude 4.02+3.02=5.0ms−1, at tan−1(3.0/4.0)=37∘ east of north.
Resolving a vector
Any vector can be replaced by two perpendicular vectors, its components, which together have the same effect. A vector of magnitude V at angle θ to the horizontal has components
so the component along the direction of the angle is the cosine and the one opposite the angle is the sine. Which is which depends on where the angle is measured from, and it is worth checking the extreme cases: at θ=0 the whole vector is horizontal, and the cosine is 1.
Resolving is what makes inclined planes and projectiles tractable. A trolley of weight W=12N on a slope at 25∘ to the horizontal has a component of weight down the slope of Wsin25∘=12×0.4226=5.1N and a component into the slope of Wcos25∘=10.9N. The second is balanced by the normal contact force of the slope.
Density
The density of a material is its mass per unit volume.
ρ (rho) is in kgm−3, m in kg and V in m3. Water is about 1000kgm−3, which is 1.00gcm−3, and since 1gcm−3=103kgm−3 the conversion between the two is a factor of 1000.
For a uniform object the density is that of the material. A steel sphere of radius 1.5cm and mass 0.109kg has a volume 34πr3=34π(0.015)3=1.41×10−5m3 and a density of 0.109/1.41×10−5=7.7×103kgm−3.
The volumes needed are πr2h for a cylinder, lwh for a rectangular block and 34πr3 for a sphere.
Measuring the density of a solid
For a regular solid, measure the mass on a balance and the dimensions with instruments matched to their size: a metre rule for lengths of tens of centimetres, vernier callipers for lengths of a few centimetres and a micrometer screw gauge for small diameters such as a wire. Repeat each length in several places and take a mean, because real objects are not perfectly uniform, and check the zero reading of each instrument first, since a zero error is a systematic error that does not average out.
The volume is worked out from the mean dimensions, and the percentage uncertainty in the density is the sum of the percentage uncertainty in the mass and the percentage uncertainties in each length, counting a length twice if it is squared and three times if it is cubed. So the smallest dimension is usually the one that limits the precision: a thin rod's diameter enters as d2, and a small absolute error in it matters much more than one in its length.
For an irregular solid, the volume can be found by displacement. Lower the object into a measuring cylinder of water and read the rise in level, or use a displacement can and collect the water that overflows. The object must be fully submerged, bubbles on its surface removed, and the scale read at eye level at the bottom of the meniscus.
I jeszcze 51: otwórz dowolne z nich z powyższej listy.
Opinie
Nie ma jeszcze pisemnych opinii. Dodaj te notatki do swoich, a możesz być pierwszą osobą, która doda opinię.