SQA National 5 Graphic Communication
cookie가 만든 복습 노트 28개예요. 과정의 주제에 따라 11개 섹션으로 구성돼요.
Notes for SQA National 5 Graphic Communication (C835 75), in folders for the eleven areas of the course's content in the specification's order, from computer-aided design and drawing standards to safe working and the preliminary, production and promotional graphics. Each note has worked examples of its own. Delete any folder your course leaves out once the notes are yours.
포함된 내용
첫 번째 노트
Computer-aided design / 2D CAD drawing commands
Computer-aided design, or CAD, produces drawings by building them from entities: lines, circles, arcs and the other shapes the software places on screen. Each entity keeps its size and position as numbers, so it can be edited later without redrawing the whole drawing. A 2D CAD package offers a small set of generic commands, and most drawings are made by combining them.
Drawing commands
The drawing commands create new entities.
- Line draws a straight line between two points.
- Circle draws a closed round shape from a set centre and radius (or diameter).
- Arc draws part of a circle between two points on it.
- Ellipse draws an oval shape from a centre and two axes.
- Rectangle draws a four-sided shape with right-angled corners in one action, so it is quicker than drawing four lines.
- Pattern fill fills an enclosed area with a repeated pattern, such as hatching for a cut surface.
Editing commands
The editing commands change entities that already exist.
| Command | What it does |
|---|---|
| Copy | Makes a copy of the selected entities, leaving the original in place |
| Mirror | Makes a reflected copy of the selected entities about a line |
| Rotate | Turns the selected entities around a point |
| Scale | Changes the size of the selected entities by a set factor |
| Trim | Removes part of an entity up to a boundary |
| Chamfer | Cuts a flat bevel across the corner where two lines meet |
| Fillet | Rounds the corner where two lines meet |
Scale and rotate act on the selected entities as a group, which is why a symmetrical part can be drawn once and mirrored to complete it. A chamfer and a fillet both change a sharp corner, one into a flat cut and the other into a curve, so each is a single command rather than hand-drawn geometry.
Worked example
A bracket has a 40 mm wide flat base and a corner that must be cut back by a 5 mm chamfer. The chamfer is applied to the corner after the two edges have been drawn, and the software then trims the two lines to the new edge. The dimension the drawing carries is the length of the cut along each edge, so the 5 mm chamfer is drawn as 5 mm along the base and 5 mm up the side. The base remains 40 mm overall, and the chamfer does not change that figure, only the corner.
Zoom and view
The zoom command changes how much of the drawing is shown on screen. It does not change the size of anything in the drawing, so a 25 mm line stays 25 mm however far in or out the view is. Zoom extents is the setting that fits the whole drawing into the window. Zooming in is useful for checking small detail, such as a tight fillet, and zooming out gives an overview of the page layout.
Layers
A layer is a level in the drawing that holds related entities, such as the outline, the dimensions, the centre lines and the hatching. Each layer can be shown, hidden, locked or changed without affecting the others. A user puts the dimensions on their own layer so that they can be switched off while the outline is checked, and then switched back on for the final printed drawing.
Snap, grid and guidelines
Snap locks the cursor to set points so that entities start and finish exactly where intended. A grid is a set of evenly spaced points that help align entities, and snapping to the grid keeps lines at regular positions. Without snap, a line drawn by eye would end a fraction of a millimetre away from the corner it should meet, and the error would show when the drawing is dimensioned.
Templates
A CAD template is a saved set-up with the page size, the units and the layers already chosen. Starting from a template saves time, and it keeps several drawings in the same format, so that they can be compared or printed together.
Import and export
The import command brings in a file made in another program, and the export command saves a drawing in a format another program can open. Export is what allows a drawing to be sent to a printer, a plotter or a manufacturer who uses different software.
그 밖에 27개 더 있어요. 위 목록에서 원하는 항목을 열어 보세요.
평가
아직 작성된 후기가 없어요. 이 노트를 내 노트에 추가하면 가장 먼저 후기를 남길 수 있어요.