Langsung ke konten

Eduqas GCSE Electronics

GCSE · EduqasElectronics20 catatan dalam 9 folder, 66 KB

20 catatan belajar, dibuat oleh cookie, dalam 9 bagian yang mengikuti topik kursus.

Notes for Eduqas GCSE (9-1) Electronics (WJEC C490), in folders for the specification's topics in its order: systems, resistors, switching, logic, amplifiers, timing, interfacing and design. Follows the 2017 specification, version 5 (December 2025).

Isi di dalamnya

Catatan pertama

Systems and circuit concepts / Electronic systems and sub-systems

Most electronic systems can be described as three sub-systems working in a chain: a sensing sub-system, a processing sub-system and an output sub-system. The sensing sub-system detects something in the physical world and turns it into an electrical signal. The processing sub-system decides what to do with that signal. The output sub-system does something visible, audible or physical with the result. A burglar alarm, an automatic night light and a washing machine's door interlock all fit this pattern, even though they look very different.

Sensing sub-systems

A sensor is a transducer, a component that converts one form of energy into another. Each sensor responds to a particular quantity:

Quantity detectedTypical sensor
LightLight dependent resistor (LDR)
TemperatureThermistor (negative temperature coefficient)
Magnetic fieldMagnetic field sensor or reed switch
PressurePressure sensor
MoistureMoisture sensor (two electrodes that change resistance when wet)
SoundMicrophone
RotationPotentiometer or rotary sensor

Most sensors change their resistance, not their output voltage directly. A sensor's resistance is therefore turned into a voltage by placing it in a voltage divider, which is covered in the note on voltage dividers. The output of a sensing sub-system is usually an analogue voltage that varies smoothly with the quantity being measured.

Processing sub-systems

The processing sub-system takes the signal from the sensor and produces a decision. The building blocks are:

  • logic gates (NOT, AND, OR, NAND and NOR), which combine digital signals;
  • a latch, which stores a single bit so that the output holds its value after the input changes;
  • a time delay, usually an RC network or a 555 timer, which holds a signal for a set time;
  • a comparator, which compares an input voltage with a reference voltage and gives a high or low output.

A comparator is the usual link between an analogue sensor and digital logic, because it turns a voltage that varies continuously into one of two levels.

Output sub-systems

Output devices change electrical energy into another form:

  • a lamp or LED produces light;
  • a buzzer or loudspeaker produces sound;
  • a solenoid uses an electromagnet to push or pull a plunger in a straight line;
  • a motor produces continuous rotation;
  • an actuator, such as a servo, turns through a set angle under the control of an input signal.

Each output device needs a particular current and voltage to work. A motor, for example, may need far more current than a logic gate can supply.

Transducer drivers

A transducer driver is the circuit between a processing sub-system and an output device. A logic output cannot usually supply enough current to drive a motor, a relay coil or a lamp directly, so the driver switches the larger current from a separate supply. An n-channel MOSFET or an npn transistor is often used for this, because a small signal at the gate or base controls a large current through the load. The driver therefore protects the processing sub-system from the load and allows the output device to run from a suitable supply.

Designing and testing a system

A system is designed by stating what it must do, dividing it into sub-systems, and choosing components for each one. Each sub-system is then built and tested on its own before the sub-systems are connected. This makes faults easier to find: if the whole system fails, the test results show which sub-system to check first.

A block diagram is the usual way to show the design. Each sub-system is drawn as a labelled box, with arrows showing the direction of the signals between them. The arrows matter as much as the boxes, because they show which sub-system depends on which.

Dan 19 lainnya: buka yang kamu mau dari daftar di atas.

Ulasan

Belum ada ulasan tertulis. Tambahkan catatan ini ke catatanmu dan jadilah yang pertama memberi ulasan.