Irish Leaving Certificate Physics
45 ملاحظات للمذاكرة لمادة SEC Leaving Certificate Physics، أعدّها cookie، في 5 أقسام تتبع موضوعات المنهج.
Notes for Irish Leaving Certificate Physics (SEC, the new NCCA specification in schools from September 2025 and first examined in 2027), in a folder for the nature of science and one for each of the four content strands in the specification's order, with one note for each topic. Practical investigations sit in the topics they belong to, and Higher level only content is marked where it sits.
ما المحتوى؟
الملاحظة الأولى
The nature of science / Units, measurement and estimation
Fundamental and derived units
Every physical quantity is a number multiplied by a unit, and a number with no unit tells you nothing. Physics builds its units from a small set of fundamental (base) units in the International System, known as SI. The ones used in this course are the metre (m) for length, the kilogram (kg) for mass, the second (s) for time, the ampere (A) for electric current and the kelvin (K) for temperature. The mole and the candela complete the set of seven but rarely appear here.
All other units are derived: they are combinations of the fundamental ones, found by following the definition of the quantity. Speed is distance over time, so its unit is ms−1. Acceleration is change of speed over time, so its unit is ms−2. Force is mass times acceleration, so one newton is 1kgms−2. Several derived units have their own names because the combination is used so often.
| Quantity | Unit | Symbol | In base units |
|---|---|---|---|
| Force | newton | N | kgms−2 |
| Energy, work | joule | J | kgm2s−2 |
| Power | watt | W | kgm2s−3 |
| Pressure | pascal | Pa | kgm−1s−2 |
| Charge | coulomb | C | As |
| Potential difference | volt | V | kgm2s−3A−1 |
| Resistance | ohm | Ω | kgm2s−3A−2 |
| Frequency | hertz | Hz | s−1 |
Temperature is usually measured in degrees Celsius in the laboratory, but the SI unit is the kelvin, and a change of one degree Celsius is the same size as a change of one kelvin.
Prefixes and powers of ten
Very large and very small quantities are written with a prefix, or in standard form as a number between 1 and 10 multiplied by a power of ten.
| Prefix | Symbol | Factor |
|---|---|---|
| pico | p | 10−12 |
| nano | n | 10−9 |
| micro | μ | 10−6 |
| milli | m | 10−3 |
| centi | c | 10−2 |
| kilo | k | 103 |
| mega | M | 106 |
| giga | G | 109 |
| tera | T | 1012 |
Converting between units means multiplying by a factor equal to one. To change a speed of 72kmh−1 into metres per second, write
Take care with units raised to a power, because a conversion factor is raised to the same power. There are 1003=106 cubic centimetres in a cubic metre, not 100, so a density of 1000kgm−3 is 1000kg in 106cm3, which is 1gcm−3.
Equations in this course are written for SI units. If you substitute a mass in grams or a length in centimetres without converting, the answer comes out in the wrong unit, and the error is easy to miss.
Significant figures
The number of significant figures in an answer tells the reader how precisely it is known. Leading zeros are not significant, so 0.00420 has three significant figures, and trailing zeros after a decimal point are. A number such as 1500 is ambiguous, and writing it as 1.5×103 or 1.50×103 settles which is meant.
In a calculation, carry extra figures through the working and round only at the end. The answer is given to the same number of significant figures as the least precise quantity that went into it. If a length of 2.35m and a time of 1.2s give a speed, the result is 2.35/1.2=1.958…, which is reported as 2.0ms−1, because the time has only two significant figures. Giving 1.958333ms−1 would claim a precision that the measurements never had.
Quantities that are counted or defined exactly, such as the 2 in 2πr or the number of oscillations in a timing, do not limit the number of significant figures.
Order of magnitude and estimation
The order of magnitude of a quantity is its value rounded to the nearest power of ten. The distance to the Moon, about 3.8×108m, is of order 109m, and the diameter of an atom, about 10−10m, is of order 10−10m. Comparing orders of magnitude shows how different two scales are: a nucleus, at about 10−15m, is roughly a hundred thousand times smaller than the atom around it.
An estimate uses round numbers and simple reasoning to find an answer that is correct to within a factor of ten or so. It is useful for checking that a calculated answer is sensible before anything else is done with it.
Worked example: estimate the mass of the air in a classroom. A room about 8m by 6m with a ceiling 3m high has a volume of about 8×6×3=144m3, which is of order 102m3. Air has a density of about 1.2kgm−3, so the mass is about 144×1.2≈170kg, of order 102kg. A result of 0.2kg or of 2×105kg would be clearly wrong.
Unit analysis
Both sides of a correct physical equation have the same dimensions, meaning the same combination of base units. Checking this is called dimensional or unit analysis, and it catches a wrong formula or a slip in rearranging one. It cannot find a missing dimensionless factor such as 2π or 21, so a formula can pass the check and still be wrong by that factor.
To test the pendulum formula T=2πl/g, look at the units of the expression under the root. A length divided by an acceleration is
and the square root is a second, which is the unit of a period. The formula passes.
The same method shows that 21mv2 is an energy. Mass times speed squared has units kgm2s−2, which is a joule. Kinetic energy and work therefore have the same unit, which is why one can be converted into the other.
Units also give a quick test of a final answer. If the question asks for a time and your working ends in ms−1, something was inverted along the way.
و44 أخرى: افتح أياً منها من القائمة أعلاه.
التقييمات
لا توجد مراجعات مكتوبة بعد. أضف هذه الملاحظات إلى مجموعتك، ويمكنك أن تكون أول من يكتب مراجعة.