انتقل إلى المحتوى
cookie

WJEC GCSE Physics

GCSE · WJECPhysics37 ملاحظة في 15 مجلدًا، 189 KB

37 ملاحظات للمذاكرة، أعدّها cookie، في 3 أقسام تتبع موضوعات المنهج.

Notes for WJEC GCSE Physics (3420, the Wales specification), in folders for its three units, with a sub-folder for each topic in the order the specification gives them. The specified practicals sit in the topics they belong to, Higher-tier content is marked where it sits, and a final folder covers scientific enquiry skills, terminology and mathematical skills. Delete any note your tier does not need once the notes are yours.

ما المحتوى؟

الملاحظة الأولى

Electricity, energy and waves / Electric circuits / Circuit components, current and potential difference

Circuit symbols

Circuits are drawn with standard symbols so that any diagram can be read and built by anyone.

ComponentHow it is drawnWhat it does
Cella long thin line and a short thick linesupplies potential difference
Switcha gap in the wire, closed when the gap is filledopens and closes the circuit
Lampa circle with a cross insidetransfers electrical energy to light and heat
Fixed resistora small rectanglelimits current
Variable resistora rectangle with an arrow through itresistance can be changed by hand
Fusea rectangle with a line through its lengthmelts if the current is too large
Diodea triangle pointing at a barlets current pass in one direction only
LEDa diode with two arrows pointing awaya diode that gives out light
Thermistora rectangle with a curved line through itresistance depends on temperature
LDRa rectangle in a circle, with two arrows pointing inresistance depends on light intensity
Ammeterthe letter A in a circlemeasures current
Voltmeterthe letter V in a circlemeasures potential difference

Two or more cells joined end to end make a battery.

Current and potential difference

An electric current is a flow of electric charge. In a metal the charge is carried by electrons, which are free to drift through the lattice of positive ions. Current is measured in amperes (A), and it can only flow round a complete loop, so opening a switch anywhere in a series loop stops the current everywhere in it.

Potential difference (p.d., also called voltage) is what pushes the charge round. It is measured in volts (V) and describes how much energy each unit of charge transfers as it passes between two points, for example across a lamp. A cell or power supply provides the p.d.; the components in the circuit transfer that energy onwards.

Conventional current is drawn flowing from the positive terminal of the cell round to the negative terminal, even though the electrons in a metal move the other way.

Measuring current and p.d.

An ammeter is connected in series with the component, so that the current passes through the meter. A voltmeter is connected in parallel across the component, because it measures the difference in potential between the two ends. A good ammeter has very low resistance and a good voltmeter has very high resistance, so that neither changes the circuit it is measuring.

Resistance and the relationship between I, V and R

The resistance of a component is a measure of how strongly it opposes the flow of current. Electrons drifting through a metal collide with the vibrating ions, which transfers energy to the lattice and heats the material. The larger the resistance, the smaller the current for a given p.d. The unit is the ohm (Ω\Omega).

I=VRI = \frac{V}{R}

Here II is the current in amperes, VV is the potential difference in volts and RR is the resistance in ohms. Rearranged, V=IRV = IR and R=V/IR = V/I.

Worked example

A lamp has a resistance of 24 Ω\Omega and is connected across a 12 V supply.

I=VR=1224=0.50 A \begin{aligned} I &= \frac{V}{R} \\ &= \frac{12}{24} \\ &= 0.50\ \mathrm{A} \end{aligned}

If a resistor carries 0.15 A when the p.d. across it is 6.0 V, its resistance is R=6.0/0.15=40 ΩR = 6.0 / 0.15 = 40\ \Omega.

Current and p.d. in the two kinds of circuit

In a series circuit there is one path for the current, so the current has the same value at every point. The p.d.s across the separate components add up to the p.d. of the supply.

In a parallel circuit the current has a choice of paths, called branches. The p.d. across every branch is the same as the supply p.d. The currents in the branches add up to the current drawn from the supply.

A series circuit is simple, but one broken component switches everything off. In a parallel circuit each branch works independently, which is why the lights in a house are wired in parallel: one failed bulb does not darken the rest.

Worked example

Three lamps are connected in series across a 9.0 V supply. The p.d. across the first is 2.5 V and across the second 4.0 V. The third must therefore take 9.0−2.5−4.0=2.59.0 - 2.5 - 4.0 = 2.5 V.

Two resistors are connected in parallel to a cell. The ammeter in the main wire reads 0.80 A and the ammeter in one branch reads 0.30 A. The other branch carries 0.80−0.30=0.500.80 - 0.30 = 0.50 A, and both resistors have the same p.d. across them.

How adding components changes the total resistance

Each extra component in series gives the charge another obstacle in the same path, so the total resistance goes up. Each extra component in parallel gives the charge another path to take, so the total current from the supply rises and the total resistance goes down.

و36 أخرى: افتح أياً منها من القائمة أعلاه.

التقييمات

لا توجد مراجعات مكتوبة بعد. أضف هذه الملاحظات إلى مجموعتك، ويمكنك أن تكون أول من يكتب مراجعة.